logo
Startseite Nachrichten

Firmenblog über TI TPS1H000 Automotive Single-Channel Smart High-Side Switch With Adjustable Current Limit

Bescheinigung
China ShenZhen Mingjiada Electronics Co.,Ltd. zertifizierungen
China ShenZhen Mingjiada Electronics Co.,Ltd. zertifizierungen
Kunden-Berichte
Versendet sehr schnell, und sehr hilfreich, neu und ursprünglich, würde in hohem Grade sich empfehlen.

—— Nishikawa aus Japan

Berufs- und schneller Service, annehmbare Preise für Waren. ausgezeichnete Kommunikation, Produkt wie erwartet. Ich empfehle in hohem Grade diesen Lieferanten.

—— Luis aus den Vereinigten Staaten

Hohe Qualität und zuverlässige Leistung: "Die elektronischen Komponenten, die wir von [ShenZhen Mingjiada Electronics Co., Ltd.] erhalten haben, sind von hoher Qualität und haben eine zuverlässige Leistung in unseren Geräten gezeigt".

—— Richardg aus Deutschland

Wettbewerbsfähige Preisgestaltung: Die von der E-Commerce-Firma angebotenen Preise sind sehr wettbewerbsfähig, was sie zu einer ausgezeichneten Wahl für unsere Beschaffungsbedürfnisse macht.

—— Tim aus Malaysia

Der Kundenservice ist hervorragend, immer hilfsbereit und sorgt dafür, dass unsere Bedürfnisse schnell erfüllt werden.

—— Vincent aus Russland

Tolle Preise, schnelle Lieferung und erstklassiger Kundenservice.

—— Nishikawa aus Japan

Zuverlässige Komponenten, schneller Versand und hervorragender Support.

—— Sam aus den Vereinigten Staaten

Ich empfehle Shenzhen Mingjiada Electronics Co., Ltd. für jedes Elektronikprojekt!

—— Lina aus Deutschland

Ich bin online Chat Jetzt
Firma Blog
TI TPS1H000 Automotive Single-Channel Smart High-Side Switch With Adjustable Current Limit
Neueste Unternehmensnachrichten über TI TPS1H000 Automotive Single-Channel Smart High-Side Switch With Adjustable Current Limit

Shenzhen Mingjiada Electronics Co., Ltd. supplies the TI TPS1H000 automotive-grade single-channel intelligent high-side switch with adjustable current limiting.

 

I. TPS1H000 Device Positioning and General Overview

The TPS1H000 is an automotive-grade certified single-channel intelligent high-side power switch launched by TI. It is rated for operating voltages ranging from 3.4V to 40V and integrates an NMOS power field-effect transistor with a typical on-resistance of 1000mΩ (1Ω), as well as a built-in charge pump, gate driver, protection circuitry and digital diagnostic unit. Designed for in-vehicle power distribution and load driving applications, the device can be connected directly in series between the battery and the load to provide integrated functions including on/off control, overcurrent limiting, fault protection and status feedback. It is suitable for high-side switching applications in body lighting, relay driving, ADAS sensor power supply, and various resistive, inductive and capacitive loads.

 

Compared with traditional discrete solutions, the TPS1H000 integrates the power transistor, driver, current limiting, protection and diagnostics within a single HVSSOP-8 package, requiring only a small number of external resistor-capacitor components to operate; Its most notable design feature is the ability to flexibly set the current-limiting threshold via an external resistor, whilst supporting three output behaviour strategies following current limiting, enabling engineers to balance functionality, cost and thermal dissipation according to the specific load.

 

II. Core Electrical Specifications and Power Stage Architecture of the TPS1H000

In terms of the power stage, the TPS1H000 integrates a single-channel NMOS power FET with a typical on-resistance (rDS(on)) of 1000 mΩ at 25°C and approximately 2000 mΩ at 150°C, making it suitable for small-to-medium current automotive loads ranging from several hundred milliamps to 1 A. The nominal DC load current range is 0 to 1 A, with a maximum output current (Imax) of approximately 0.9 A.

 

In terms of power supply and power consumption characteristics, the device has a wide operating voltage range of 3.4 V to 40 V, with a recommended operating voltage of 4 V to 40 V. It can be directly connected to a 12 V vehicle battery bus and possesses a certain degree of load dump tolerance. The shutdown standby current is less than 500 nA (typically 0.5 µA at 25°C), which helps to reduce static power consumption during prolonged periods when the vehicle is switched off and stationary; the standby current when diagnostics are enabled is approximately 3 mA. The high-level threshold for the logic input IN and the diagnostic enable (DIAG_EN) is 2 V, whilst the low-level threshold is 0.8 V; these can be connected directly to 3.3 V or 5 V MCU I/O ports. The pins feature internal pull-up and pull-down resistors and provide protection for the MCU I/O.

 

The power stage also incorporates a drain-to-source clamp; when switching off an inductive load, the internal negative voltage clamp absorbs the inductive feedback energy, dissipating approximately 40 mJ per pulse, thereby reducing the design burden associated with external freewheeling and clamping networks.

 

III. In-depth Analysis of the TPS1H000’s Adjustable Current-Limiting Mechanism

Adjustable current limiting is a core function of the TPS1H000. It is designed to clamp the output current at a preset level during inrush, short-circuit to ground or overload conditions, thereby preventing damage to the load, wiring harnesses, connectors and upstream power supplies caused by overcurrent stress; at the same time, the precise current-limiting values allow the system to reduce PCB trace widths, connector wire gauges and upstream power supply capacity in accordance with actual load specifications, thereby reducing system costs.

 

1. Dual Current-Limiting Threshold Architecture

The device provides two thresholds: an internal fixed current limit and an externally adjustable current limit. The internal current limit (ICL (int)) is fixed at approximately 1 A to 1.8 A and is enabled when the CL pin is directly connected to ground; this is suitable for applications that permit higher transient currents; The external adjustable current limit is set by connecting an external resistor R_CL between the CL pin and the device ground; the current limit threshold can be flexibly configured between 0.05 A and 1 A, allowing the protection point to be tailored to the load’s rated current.

 

2. Method for Setting the Current Limit Value

The external current limit is determined jointly by the internal bandgap reference voltage and the current sampling ratio. The formula provided in the data sheet is: R_CL = V_CL (th) × K (CL) / I_OUT. Here, the internal reference voltage V_CL (th) is typically 0.8 V, and the current limiting ratio K (CL) is typically 600; this ratio remains constant across the full temperature and supply voltage ranges, ensuring that current limiting accuracy is minimally affected by temperature drift and bus voltage fluctuations. It should be noted that if there is a potential offset between the device ground and the board-level ground in the circuit board’s ground network, the CL pin must be connected to the device’s own ground to prevent ground bounce errors from affecting the current limit setting.

 

3. Current Limit Accuracy by Range

The accuracy of the externally adjustable current limit varies according to the current range: when the current limit value is greater than or equal to 150 mA, the accuracy is ±15 per cent; for current values greater than or equal to 300 mA and less than 1 A, the accuracy improves to ±10 per cent; for the low-current range of 50 mA to 150 mA, the accuracy is approximately ±20 per cent. This high-accuracy range covers the normal operating currents of most automotive lighting, sensors and low-power actuators, ensuring that the protection threshold avoids normal load transients whilst still triggering promptly in the event of a genuine overload.

 

4. Combination of Fast-Trip Protection and Closed-Loop Current Limiting

When IN is enabled and a sudden hard short-circuit to ground occurs at the output, the device first triggers fast-trip protection before the closed-loop current limiting circuit is established. With a typical response time of less than 1 µs, the output is rapidly switched off to suppress spike surges; Subsequently, the current-limiting closed-loop is activated, clamping the output current at the set value whilst reporting a fault via the FAULT pin. As the power FET experiences high power dissipation during clamping, the device’s junction temperature rises accordingly, after which the thermal protection circuit takes over.

 

neueste Unternehmensnachrichten über TI TPS1H000 Automotive Single-Channel Smart High-Side Switch With Adjustable Current Limit  0

 

IV. Three Configurable Behaviour Modes Following Current Limiting

When the output current reaches the current-limiting threshold, the TPS1H000 can be configured via the external connection of the DELAY pin to operate in one of three modes—hold, latch or auto-retry—corresponding to different fault-tolerance requirements.

 

1. Holding Mode

Holding mode is entered by connecting the DELAY pin directly to ground. Once current limiting is triggered, the output current is maintained at the set limit; the device relies on the power FET’s dissipation capacity to withstand the fault current. Thermal shutdown occurs when the junction temperature rises to the thermal shutdown threshold (typically 175°C). Once the fault has been cleared, if the current-limiting condition ceases whilst IN is high, the FAULT flag will clear automatically; alternatively, the fault may be cleared by pulling IN low for longer than the fault hold time t_FAULT (typically 8.5 ms). This mode is suitable for loads where short-term overloads can resolve themselves and where the device is permitted to dissipate power for a brief period.

 

2. Latch-off Mode

The device enters latch-off mode when the DELAY pin is connected to ground via a capacitor. Once current limiting is triggered, the output is first held at the current limit value for a preset delay. This delay is the sum of an internal fixed delay tdl1 (typically 300 µs to 500 µs) and an adjustable delay tdl2 configured by an external capacitor; tdl2 can be configured up to approximately 1000 ms. Once the delay has elapsed, the output is latch-off. Thereafter, even if the short-circuit or overload condition has been resolved, the output remains off; it can only be restored by toggling the IN pin. This mode is suitable for safety-critical loads where, following a fault, a manual or master control confirmation must be awaited, and autonomous power-up is not permitted.

 

3. Auto-Retry Mode (Auto-retry)

Auto-retry mode, also known as ‘hiccup’ mode, is entered when the DELAY pin is externally pulled high. Once current limiting is triggered, the output periodically attempts to switch on and off: the on-time t_hic (on) is typically 35 ms to 45 ms, and the off-time t_hic (off) is typically 0.8 s to 1.2 s. If the fault clears within a single on-cycle, the output resumes normal operation and the FAULT signal is cleared; if the fault persists, power is supplied intermittently in ‘hiccup’ mode, limiting average power consumption and heat generation to low levels. This mode is suitable for inrush surges in capacitive loads, occasional poor contacts, or automotive sub-modules requiring self-recovery.

 

V. Comprehensive Protection Mechanism System

In addition to current limiting, the TPS1H000 integrates multi-layered protection designed for harsh automotive operating conditions.

Ground short-circuit and overload protection are achieved through a combination of closed-loop current limiting and rapid transients, covering both hard short-circuits and sustained overloads. Thermal protection comprises two stages: thermal shutdown and thermal swing. The thermal shutdown threshold is typically 175°C, with a reset threshold of typically 155°C; the thermal swing threshold is typically 60°C, with a reset hysteresis of approximately 10°C, which is used to limit the range of junction temperature fluctuations under repeated current-limiting conditions. Upon entering the thermal shutdown state, the current limit is automatically reduced to 60 per cent of the rated value to minimise power consumption.

When an inductive load is switched off, the device suppresses inductive reverse voltage via internal negative voltage clamping; it also provides appropriate protection in ‘loss-of-GND’ and ‘loss-of-battery’ scenarios to prevent abnormal operation of the device in the event of a ground fault. Undervoltage lock-out (UVLO) shuts down the output when the bus voltage drops to the 3.0 V to 3.4 V range and restarts once it recovers to the 3.5 V to 3.7 V range; the undervoltage hysteresis is approximately 0.5 V. Furthermore, it supports reverse current limiting under reverse polarity conditions and protection for MCU interface pins, thereby enhancing the reliability margin within the vehicle’s electrical environment.

 

VI. Digital Diagnostics and Status Feedback

The device provides comprehensive fault diagnosis capabilities via the FAULT digital open-drain output in conjunction with the DIAG_EN enable pin. Diagnostic types cover overload and short-to-ground detection, open-load detection, short-to-battery detection, and thermal fault detection.

 

Open-circuit load detection is one of its key diagnostic features: whilst the output is in the on-state, the device determines whether the load is open by checking whether the output current falls below the on-state open-circuit threshold (typically 1 mA to 8 mA, with a debounce time of 200 µs to 450 µs); when the output is in the off state, it determines whether the load is open by checking whether the voltage difference between the bus and the output terminal is below the open-circuit threshold for the off state (typically 1.4 V to 2.6 V). In other words, regardless of whether the switch is in the on or off state, the system can ascertain whether the load connection is normal, facilitating fault reporting to the vehicle for issues such as broken light bulbs or detached sensor harnesses.

 

Thermal shutdown and thermal oscillation are also included in the fault reporting scope; the FAULT low-level output exhibits a voltage drop of no more than 0.2 V under a 2 mA sink current, allowing direct connection to an MCU interrupt or input pin. These diagnostic functions mean that the device is not merely an electronic switch, but can also serve as a status acquisition unit for in-vehicle power distribution nodes.

 

VII. Flexibility in Stand-alone Operation and System Integration

The TPS1H000 supports both MCU-controlled and MCU-independent operating modes. In stand-alone mode, the device can perform on/off control, current limiting, protection and fault latching without the involvement of a host controller, making it suitable for isolated subsystems, simplified distribution boxes or cost-sensitive basic lighting circuits; When connected to an MCU, the host controller can control on/off switching via the IN pin, enable diagnostics via DIAG_EN, and read the FAULT status, thereby enabling vehicle-wide load management and fault logging. This flexible integration approach allows it to be used not only in simple high-side relays or LED driver channels, but also to be embedded in electronic electrical architectures requiring diagnostic reporting.

 

VIII. Automotive Certification, Reliability and Packaging

The device complies with automotive application requirements and is AEC-Q100 certified: its environmental operating temperature class is Class 1, with a range of –40°C to 125°C; for ESD, its HBM classification is H2 and its CDM classification is C4B. The operating junction temperature range is -40°C to 150°C, with a storage temperature range of -65°C to 150°C. The device is housed in an 8-pin HVSSOP (DGN) package, measuring approximately 3 mm × 4.9 mm, and features an exposed heat sink pad to facilitate the transfer of heat from the power transistor to the PCB copper foil; part number TPS1H000AQDGNRQ1, with NiPdAu pin plating, meets the reliability requirements for automotive reflow soldering and long-term storage.

 

IX. Typical Application Scenarios for the TPS1H000

For automotive electronics applications, the TPS1H000 is primarily suited to the following loads and circuits: single-channel LED drivers and body lighting (including interior ambient lighting, reading lights, tail lights and indicator channels); single-channel high-side relay drivers for controlling low-power relays, solenoid valves or door lock actuators; sensor power supply channels for Advanced Driver Assistance Systems (ADAS), providing high-side power distribution with diagnostics for cameras, millimetre-wave radar or ultrasonic sensors; as well as general resistive, inductive and capacitive sub-module loads. In medium-to-low-power in-vehicle power distribution nodes requiring inrush current control, short-circuit protection and open-circuit diagnosis, this device can serve as an electronic alternative or supplement to traditional relay and fuse solutions.

 

X. Design Considerations and Selection Summary

When selecting the TPS1H000, it is recommended to first determine the external current-limiting resistor R_CL based on the load’s normal operating current and permissible inrush current, and then select the DELAY pin configuration according to the fault tolerance strategy: choose ‘auto-retry’ for self-recovering loads, ‘lockout’ for safety-critical loads requiring manual confirmation, and ‘hold’ mode for loads capable of withstanding short-term faults. During PCB layout, ensure there is sufficient copper area and via count beneath the heat sink pad; ground the external components for CL and DELAY as close as possible; and pull the FAULT line up to the power domain on the controller side. Overall, the TPS1H000, with an on-resistance of 1 Ω, adjustable current limiting from 0.05 A to 1 A, three fault behaviour modes, full-condition diagnostics and comprehensive automotive-grade certification, constitutes a highly integrated single-channel high-side switch for automotive applications. It is suitable for automotive power distribution and load drive designs that require protection accuracy, fault observability and a streamlined Bill of Materials (BOM).

Kneipen-Zeit : 2026-11-18 15:50:20 >> Nachrichtenliste
Kontaktdaten
ShenZhen Mingjiada Electronics Co.,Ltd.

Ansprechpartner: Mr. Sales Manager

Telefon: 86-13410018555

Faxen: 86-0755-83957753

Senden Sie Ihre Anfrage direkt an uns (0 / 3000)